Stainless Steel C Clamp with Eye Bolt
Youjia Metals supplies a stainless steel C clamp with eye bolt for beam mounting, pipe support hardware and industrial equipment assemblies. Eye bolt, wing nut and hex-bolt configurations can be reviewed for different installation needs. Dimensions and application suitability are confirmed from drawings, samples or project requirements.
Request a QuoteProduct Overview
This C clamp with eye bolt and wing nut is designed as reusable beam mounting hardware where a drilled connection is not preferred. The C-shaped body fits over an edge or beam flange, while the threaded fastener provides adjustable contact. It can be supplied as a universal beam clamp with eye bolt, an eye-bolt version with a separate wing-nut option, or a hex-bolt configuration according to the approved design.
The page describes industrial mounting hardware only. Final material grade, dimensions, mating surface, installation method and application suitability must be confirmed before production or use.
C Clamp Dimensions
Use the specification table below when requesting a quote. Unknown values are not assumed; they are reviewed against your drawing, sample or mounting conditions.
| Product type | Stainless steel C clamp with eye bolt |
|---|---|
| Thread size | Confirm according to drawing or sample |
| Jaw opening | Confirm according to required mounting range |
| Beam thickness range | Confirm according to beam or edge dimensions |
| Eye bolt size | Confirm according to connection requirement |
| Material grade | SS304 or SS316, subject to order confirmation |
| Surface finish | Polished, passivated or project-specific finish, subject to confirmation |
| Application | Beam mounting hardware, pipe support hardware and industrial assemblies |
| OEM supply | Custom dimensions and configurations from drawings or samples |
Eye Bolt and Wing Nut Options
An adjustable C clamp with eye bolt provides a connection point while allowing the clamping position to be set for the mounting surface. Wing-nut and hex-bolt configurations can also be reviewed. The correct thread form, engagement length and tightening method depend on the approved drawing and installation.
Material and Surface Finish
SS304 and SS316 are available for applications requiring corrosion-resistant stainless steel hardware. An SS304 beam clamp or SS316 beam clamp should be selected after considering exposure, cleaning chemicals and service environment. Surface condition and passivation requirements can be specified on the drawing.
Beam and Pipe Mounting Applications
This product is commonly reviewed as a C clamp for beam mounting, stainless steel pipe support clamp, industrial C clamp hardware or C clamp mounting bracket. Possible uses include equipment frames, support rails, pipe-support assemblies, sensor brackets and general industrial mounting points.
For projects described as a beam clamp for hanging equipment or heavy duty stainless steel C clamp, suitability must be confirmed by the purchaser’s engineer using the actual geometry, material, substrate and service conditions. No rated capacity is implied by these descriptions.
Installation Notes
- Confirm jaw opening and beam thickness before ordering.
- Use the specified thread size and ensure adequate thread engagement.
- Install against a clean, stable contact surface without side loading.
- Check tightening method and inspection frequency for the application.
- Do not use the clamp in a safety-critical or rated application without engineering approval and appropriate validation.
OEM and Custom Manufacturing
As a custom C clamp manufacturer and stainless steel beam clamp supplier, Youjia Metals supports drawing-based production for custom jaw openings, eye-bolt dimensions, thread sizes, body geometry and surface finishes. A drawing, sample or clear installation information helps us review manufacturability and prepare an accurate quotation.
Quality Inspection
Inspection requirements should be agreed before production. Typical checks can include material confirmation, overall dimensions, jaw opening, thread size, eye-bolt geometry, contact surfaces, visible edges and surface condition. Functional fit should be reviewed with the actual beam, edge or mating component whenever the installation interface is critical.
For repeat orders, an approved drawing or sample provides the most reliable reference. Any requested material document, dimensional report, finish requirement or packaging label should be listed in the purchase specification rather than assumed after production.
Related Custom Hardware
Buyers comparing mounting solutions can review our custom hardware parts, stainless steel pipe clamp and custom metal mounting straps. These links cover alternative mounting forms; final selection should follow the installation drawing and service conditions.
FAQ
What is a stainless steel C clamp with eye bolt used for?
It is used as adjustable beam mounting hardware or pipe support hardware in industrial assemblies. The final use must match the confirmed drawing and installation conditions.
Can you supply a C clamp with eye bolt and wing nut?
Yes. Eye-bolt, wing-nut and hex-bolt configurations can be reviewed according to the required adjustment and installation method.
Are SS304 and SS316 available?
SS304 and SS316 options are available, subject to confirmation for the selected design, quantity and application environment.
Can jaw opening and thread size be customized?
Yes. Jaw opening, thread size, eye-bolt size and other dimensions can be produced from an approved drawing or sample.
How do I confirm whether the clamp is suitable?
Please provide the mounting surface, beam or pipe dimensions, service environment and intended use. Application suitability is subject to engineering confirmation.
Send Your Drawing or Application Details
Request an OEM quotation for a stainless steel beam clamp with the dimensions, material and finish your project requires.
Request a Quote
Reviews
There are no reviews yet.